Grabber

hgc-hgh

Produced in HGHxx, HGCxxA, and HGCxxO models with 8, 10, and 12 bale capacity, and designed for easy attachment to front-loader, Bobcat or similar machineries, this grabber can act as a great help for lifting, loading and unloading bales of hay and forage, and saves the farmer lots of time, energy and money. In addition to that, the HGCxxA model, in beneath, is equipped with a canal for the picked bales to sort, so that no single bale on the field would be out of its reach. Only HGCxxA model is equipped with this feature and other models don`t have it. The HGHxx Grabber model attachess to front-loaders or other machines through a hinge.

The grabber is equipped with a hydraulic jack which pushes the hooks into square bales or takes it out. For this feature to work, you need to connect an extra hydraulic lever valve or such thing to control the valves of front loader.

The HSSH Grabber is designed in various models for various functions and tasks. Based on whether it is attached to bobcat or front loader, we have HGC and HGH, the former is attached to the front loader from its backside and enjoys at least two vertical walls beneath it, and the latter, is attached to the front loader through the over hinge and a special arm, so it does not need  those walls.

HGC08A and HGC10A models can almost do the job of our Collectors in collecting the hay and forage from the ground. If being dragged does not damage the square bales or the field is ready for them to be dragged on, driving on the field the device sends square bales into canals beneath the grabber and when it reaches the maximum capacity, the front-loader-attached grabber comes in to lift them.

HGC10A and HGC08A grabber models are recommended for collecting and loading square bales. And to load and unload the square bales collected, sorted, and left in bunches on the field using our Collectors, the HGC10O and HGC08O grabbers are recommended. (The HGC08A and HGC10A grabbers can do the same job but are heavier and bigger in comparison) and finally, to unload and stack the square bales in farms warehouse, HGH08 and HGH10 series are recommended.  

HGC

HGC10A and HGC08A grabber series

 

HGC08A model technical specifications

Weight without bales

330kg

Length

208cm

Maximum width

260cm

Minimum width

 230cm

Height

80cm

Hooks

16

Needed oil pressure

120 to 180 bar

Minimum power of tractor

60 horsepower

Front loader`s capacity

800kg

 

 

hgc2

HGC10O and HGC08O grabber model

 

HGC08O model technical specifications

Weight without bales

200kg

Length

208cm

Maximum width

240cm

Minimum width

225cm

Height

80cm

Hooks

16

Needed oil pressure

120 to 180 bar

Minimum power of tractor

50 horsepower

Front loader’s capacity (pivot point at full height)

700kg

 

HGC10O model technical specifications

Weight without bales

230kg

Length

250cm

Maximum width

240cm

Minimum width

225cm

Height

80cm

Hooks

20

Needed oil pressure

120 to 180 bar

Minimum power of tractor

55 horsepower

Front loader’s capacity (pivot point at full height)

850kg

 

Various HGC series attachment to front loader

 

HGH grabber series

Because of the attachment, the front loader`s lifting height increases up to at least 50 cm

 

HGH08 model technical specifications

Weight without bales

600kg

Length

380cm

Maximum width

280cm

Minimum width

-

Height

140cm

Hooks

16

Needed oil pressure

120 to 180 bar

Minimum power of tractor

55 horsepower

Front loader’s capacity (pivot point at full height)

850kg

 

HGH10 model technical specifications

Weight without bales

600kg

Length

380cm

Maximum width

280cm

Minimum width

-

Height

140cm

Hooks

16

Needed oil pressure

120 to 180 bar

Minimum power of tractor

55 horsepower

Front loader’s capacity (pivot point at full height)

850kg

 

Approximate dimension sizes of each square bale, and the bunch created by device in 8, 10, and 12 bale size

Square bales specifications

Height (cm)

36±3

Length (cm)

100±10

Width (cm)

46±3

 

Notice:

A) To find out the weight and power of the front loader you want to attach the grabbers to, check the manual of your machine in advance.

B) It is feasible to add more hooks to the device to keep the square bales tighter. For all the products introduced above, two hooks have been accounted for each square bale. 

JoomShaper